favorite
favorite
hide
unhide
flag

Posted

print

CEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # - $9,999 (Eugene)

CEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 1 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 2 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 3 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 4 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 5 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 6 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 7 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 8 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 9 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 10 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 11 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 12 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 13 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 14 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 15 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 16 thumbnailCEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # 17 thumbnail
90925 Prairie Road near Awbrey

google map

make / manufacturer: Cemco
model name / number: 3-head sander
PLEASE NOTE - If you choose to email, please ***check your spam for replies!!!*** - or - you can call 541.5O1.5969 (sorry, no texts)

CEMCO 48" 3 Head Sander w/ one 75 HP motor & 2 50 HP motors ~ Serial # WBS-197

* Very dependable machine
* 1st Head: Hard rubber: sand lumber surface, particle board, MBF
* 2nd Head: 65 lb Soft: For veneers, hardwood, 120 grit, #3 hardware, takes 4/5000ths off
* 3rd Head: Smoothing bar. 4" wide, contact is about 4", takes 2-3/1000ths off
* Spare 2nd Head Included
* 51 x 120" Feed-Through Belt ijstcd
* Belt Tracking
* Includes Parts & Table
* Piping to Gate
* Can run 100 ft per minute; was operated at about 65 ft / minute
* Sealed Bearings (replacements available at McGuire Bearings if/when needed)
* Serviced by Master Machine, where staff are familiar with this unit
* Great all-in-one machine!

post id: 7744657878

posted:

updated:

best of [?]

loading
reading
writing
saving
searching